Difference between pages "File:Mendel90.zip" and "Mendel90 3D Printer"

From ENTS
(Difference between pages)
Jump to: navigation, search
(Slic3r configuration file. * Filament: Natural ABS * Layer Height: .25mm * Infill: .4 (high))
 
(Firmware/INI Files)
 
Line 1: Line 1:
Slic3r configuration file.
+
{{Template:EquipmentPage |owner=ENTS |model=Mendel90 |serial=ENTS000001 |arrived=June 2013 |doesitwork=WORKING |contact= [[User:Hov]] |where=Main Workroom |certification= YES |hackable= NO |value= $600 |itemphoto=[[File:Mendel90.jpg|350px|thumb|right|]]}}<br>
  
* Filament: Natural ABS
+
== Current State ==
* Layer Height: .25mm
+
Currently working with small issues.  Interface is at http://members.ents.ca:5000
* Infill: .4 (high)
+
 
 +
== Who Can Certify You? ==
 +
[[User:Hov]]
 +
[[User:grelli]]
 +
[[User:khawkings]]
 +
 
 +
== Specifications ==
 +
 
 +
 
 +
== Equipment Settings ==
 +
== Modifications ==
 +
The firmware has been modified to make extruder 1 (of extruders 0 and 1) behave like extruder 0.  There was a magic smoke event that cooked the current limiting resistor for the extruder 0 heater.
 +
 
 +
== What Could it Use? ==
 +
 
 +
* Kyle will be working on a Bowden Tube based extruder to move the stepper and cold end off the X-Carriage
 +
* A mounting system/brackets/case for the LCD screen
 +
* A Cover/Case/Fan Mount for the electronics
 +
 
 +
If you're willing to tackle any of these please let someone know.
 +
 
 +
== Working on it ==
 +
* [[User:khawkings]] - Bowden Tube extruder
 +
 
 +
== Known Problems ==
 +
If the hot end stops making itself hot then unplug and plug back in the connectors for the hot end on the x-carriage (the 4 pin connectors to the protoboards)
 +
 
 +
== Future Ideas ==
 +
 
 +
== Firmware/INI Files ==
 +
 
 +
* [[File:Einstein-Marlin.zip]]
 +
* [[File:Mendel90.zip]] Slic3r configuration file

Revision as of 10:52, 3 August 2013

Back to list of Equipment

Mendel90.jpg

Contents

Label

Mendel90 3D Printer http://ents.ca/index.php/Mendel90_3D_Printer

General

  • Owner/Loaner: ENTS
  • Make/Model: Mendel90
  • Usability: WORKING
  • Contact: User:Hov
  • Where: Main Workroom
  • Certification Needed: YES
  • Hackable: NO
  • Estimated Value: $600

Instructions

{{{Instructions}}}

Current State

Currently working with small issues. Interface is at http://members.ents.ca:5000

Who Can Certify You?

User:Hov User:grelli User:khawkings

Specifications

Equipment Settings

Modifications

The firmware has been modified to make extruder 1 (of extruders 0 and 1) behave like extruder 0. There was a magic smoke event that cooked the current limiting resistor for the extruder 0 heater.

What Could it Use?

  • Kyle will be working on a Bowden Tube based extruder to move the stepper and cold end off the X-Carriage
  • A mounting system/brackets/case for the LCD screen
  • A Cover/Case/Fan Mount for the electronics

If you're willing to tackle any of these please let someone know.

Working on it

Known Problems

If the hot end stops making itself hot then unplug and plug back in the connectors for the hot end on the x-carriage (the 4 pin connectors to the protoboards)

Future Ideas

Firmware/INI Files

File history

Click on a date/time to view the file as it appeared at that time.

Date/TimeDimensionsUserComment
current21:34, 16 February 2014 (1 KB)KHawkings (Talk | contribs)Updated to yellow filament config. Proven successful with multiple prints.
10:52, 3 August 2013 (1 KB)Hov (Talk | contribs)Slic3r configuration file. * Filament: Natural ABS * Layer Height: .25mm * Infill: .4 (high)

The following page links to this file:

Personal tools
Namespaces

Variants
Actions
Navigation
Members
Toolbox