Difference between pages "Signal Generator" and "Mendel90 3D Printer"

From ENTS
(Difference between pages)
Jump to: navigation, search
(Created page with "{{Template:EquipmentPage |owner=SlePP |model=BK Precision 3010 |serial=SERIAL NUMBER |arrived=Sept 2009 |doesitwork=WORKING |contact=SlePP |where=Electronics Bench |certificat...")
 
(Modifications)
 
Line 1: Line 1:
{{Template:EquipmentPage |owner=SlePP |model=BK Precision 3010 |serial=SERIAL NUMBER |arrived=Sept 2009 |doesitwork=WORKING |contact=SlePP |where=Electronics Bench |certification= NO |hackable= NO |value= <$250 |itemphoto=[[File:BK_Precision_3010.jpg|350px|thumb|right|]]}}<br>
+
{{Template:EquipmentPage |owner=ENTS |model=Mendel90 |serial=ENTS000001 |arrived=June 2013 |doesitwork=WORKING |contact= [[User:Hov]] |where=Main Workroom |certification= YES |hackable= NO |value= $600 |itemphoto=[[File:Mendel90.jpg|350px|thumb|right|]]}}<br>
 +
 
 +
 
 +
==Mendel 90==
 +
3D printing is a thing and it's a thing we can do!
 +
 
 +
== Current State ==
 +
Currently working with small issues.  Interface is at http://members.ents.ca:5000
 +
 
 +
== Who Can Certify You?==
 +
[[User:grelli]]
 +
[[User:khawkings]]
 +
 
 +
== Specifications ==
 +
 
 +
 
 +
== Equipment Settings ==
 +
== Modifications ==
 +
The firmware has been modified to make extruder 1 (of extruders 0 and 1) behave like extruder 0.  There was a magic smoke event that cooked the current limiting resistor for the extruder 0 heater.
 +
 
 +
== Working on it ==
 +
== Known Problems ==
 +
If the hot end stops making itself hot then unplug and plug back in the connectors for the hot end on the x-carriage (the 4 pin connectors to the protoboards)
 +
 
 +
== Future Ideas ==

Revision as of 18:28, 2 August 2013

Back to list of Equipment

Mendel90.jpg

Contents

Label

Mendel90 3D Printer http://ents.ca/index.php/Mendel90_3D_Printer

General

  • Owner/Loaner: ENTS
  • Make/Model: Mendel90
  • Usability: WORKING
  • Contact: User:Hov
  • Where: Main Workroom
  • Certification Needed: YES
  • Hackable: NO
  • Estimated Value: $600

How to Use

{{{Instructions}}}


Mendel 90

3D printing is a thing and it's a thing we can do!

Current State

Currently working with small issues. Interface is at http://members.ents.ca:5000

Who Can Certify You?

User:grelli User:khawkings

Specifications

Equipment Settings

Modifications

The firmware has been modified to make extruder 1 (of extruders 0 and 1) behave like extruder 0. There was a magic smoke event that cooked the current limiting resistor for the extruder 0 heater.

Working on it

Known Problems

If the hot end stops making itself hot then unplug and plug back in the connectors for the hot end on the x-carriage (the 4 pin connectors to the protoboards)

Future Ideas

Personal tools
Namespaces

Variants
Actions
Navigation
Members
Toolbox